Harga Sewa Fotocopy Murah

Harga Sewa Fotocopy Murah
Promo Sewa Fotocopy

Cara Download Software System iR6570 / iR5570

By photocopy canon | At Tuesday, November 20, 2012 | Label : , , , , , | 2 Comments
Cara Download Software System iR6570 / iR5570 ini seperti yang saya baca pada Buku Service Manual Canon iR6570 memang masih dalam bahasa aslinya, akan tetapi karena disertai gambar saya rasa tidak begitu kesulitan bagi anda untuk mengikutinya.

The system software comes in 2 types (one for use inside Japan and the other, outside Japan).
Unlike previous iR controllers, however, there is only one type of system software. (Previously, one type supported Net Ware while the other did not. There is now only one type for the machine supporting NetWare.)

Downloading Procedure System Software iR6570 / iR5570
You can run a downloading session either in normal or safe mode.
1) Select the version of the system you want to download.
version system iR6570
2) Click [Start].
Firmware Canon iR6570
3) When the session has ended, click [OK].
downloading complete iR6570
4) If you want to start another downloading session, see the appropriate instructions.
5) When you are done with downloading, turn off and then on the main power.
6) See the upgrade status indicated on the control panel. When a message appears asking you to turn off and then on the switch, turn off and then on the main power.

Be sure never to turn off the power while the machine is executing a downloading session or writing downloaded software. The ongoing session will be suspended and the machine may fail to start up.
writing downloaded software iR6570
Upgrading complete iR6570
If the machine fails to start up, format BOOTDEV using HDFormat, and then download system software to be stored in the HDD such as System, Language, and RUI.

Demikianlah “Cara Download Software System iR6570 / iR5570” moga bisa membantu bagi yang belum paham.

Enhanced by Zemanta

Tips agar karyawan Fotocopy Anda betah

By photocopy canon | At Tuesday, November 20, 2012 | Label : , , , | 0 Comments
Poncho de Anda
Poncho de Anda (Photo credit: Wikipedia)
menjaga hubungan baik anatara karyawan fotocopy dengan andaTips agar karyawan Fotocopy Anda betah, sebenarnya kalau untuk hubungan anda dengan pegawai... yang penting kepercayaan dan ketegasan anda... sulit memang cari pegawai yang jujur, tekun, dan yang mau terus belajar.

Ada baiknya, jika anda ada waktu... Pada awal anda Buka Usaha Copy Center anda sendiri yang handle dan karyawan sebagai assistant, atau karyawan sebagai pegawai utama, anda sebagai kasir...
  1. untuk cek kondisi barang dll.. Setiap mesin fotocopy punya counter.. jadi anda bisa cek berapa ribu copy yang dilakukan hari itu. tapi jangan lupa, ada yang copy tapi rusak ( dalam hal ini, misal kertas macet, kertas kusut atau hasil cetak tidak sempurna, dan kerusakan hasil cetak karena human error, misalnya salah pembesaran / pengecilan, hasil item karena lupa ditutup, dll). Kalo di tempat ane... sehari antara 1-2% dari total copy yang rusak. cek dengan penghasilan yang anda terima.
  2. Anda harus mempunyai catatan semua stok barang, termasuk stationary/atk. Jadi anda bisa cek berapa jumlah barang yang terjual dengan cek stok. anda bisa pakai excel sederhana atau aplikasi stok barang, cari aja di CCPBB banyak kok.Cek dengan penghasilan yang anda terima.
  3. Jangan pelit.
  4. Kalau pegawai anda memang punya kinerja bagus, beri bonus, insentif atau paling ga hargai usahanya dengan memberi pujian dan encouragement.
  5. Kalau bisa cari pegawai dari keluarga sendiri dulu gan...
  6. pokoknya yg latar belakang keluarganya anda tau... dan tipikal pergaulannya anda tau... jadi terpantau kepribadiannya..
  7. Jalin kedekatan dengan pegawai tsb, sharring, intinya biar pegawai tersebut menganngap anda bukan sebagai BOS, tetapi mitra kerja.. krn pada dasarnya pegawai itu bukan bawahan kita, tetapi mitra kerja kita. Dgn begitu, si pegawai merasa di manusiakan. Minta pendapatnya tentang bagaimana develop usaha anda, permintaan konsumen seperti apa, barang apa yang perlu anda lengkapi, dll...
  8. Kalo anda mmang lagi ada di toko anda, jangan asal suruh aja, kalo dia memang kerepotan, jangan segan buat membantu, dan turun langsung menghadapi konsumen... dgn begitudia merasa anda juga mau kotor...
so far itu yang ane terapin, jadi pegawai ane loyal, dari buka sampai sekarang masih sama ane gan... meskipun gaji yang ane kasi juga pas pasan... tapi suasana kekeluargaan itu bisa mengikat pegawai lebh kuat dibanding gaji lebih lho... xixixi
mungkin anda-anda yang lain bisa nambahin...
ane juga masih nubi, dan ingin belajar sama anda-anda semua. semoga bermanfaat...

Sumber: http://old.kaskus.co.id/showthread.php?t=6418637&page=4

Baca juga : Tips Usaha Copy Center
Enhanced by Zemanta

Tips Usaha Copy Center

By photocopy canon | At Tuesday, November 20, 2012 | Label : , , , | 0 Comments
Tips Usaha Copy Center untuk pemula yang ingin Buka Usaha Fotocopy
Tips buka usaha Copy Center
Harga Fotocopy | Copy Center

Mencoba pasaran dengan mesin fotocopy speed menengah contoh IR3300, IR4570 ya kalau punya dana lebih saya saranin pakai yang high speed seperti IR5000 IR6000 kalau modal tanggung pakai yang IR5570 atau IR6570, bukannya dengan mesin lama (seperti NP6650, 6050, 6030/6035). Jika prospeknya bagus, tambahkan mesin yang mempunya speed yang lebih tinggi seperti IR5020 IR6020 atau IR7200 / IR8500, IR105. Alasannya:

BIAYA - BIAYA :
1. BIAYA PERAWATAN MESIN.
Dilihat dari harga tentu mesin lama lebih murah, tapi coba bandingkan dengan biaya perawatan mobil baru dengan mobil lama. Banyak hidden cost dan yang lebih parah waktu perbaikan dan down time yg mempengaruhi produktivitas anda. Jadi kenapa tidak bayar lebih mahal sedikit tapi bebas pusing?

2. BIAYA PEMAKAIAN LISTRIK
Belum lagi biaya listrik mesin lama lebih boros daripada mesin model baru seperti ir4570/5070 yang teknologi nya hemat energi.

3. BIAYA SPAREPART
  • Pilih lah mesin rekondisi Canon karena sparepart nya lebih gampang di cari dan harganya lebih kompetitif (ibaratkan Toyota dengan Hyundai)
  • Pilihlah sparepart dengan kualitas bagus.Jangan hanya karena harga yang murah saja. Contoh: Toner A, harganya 100rb, tapi hasil kopian cuma 10rb lembar (1 lembar: Rp 10). Sedangkan toner B, harga 110rb tapi hasil kopian 15rb lembar (1 lembar: Rp 7.3).Nah bedanya jauhkan?
  • (hasil kopian juga dipengaruhi setting kehitaman mesin fotocopy anda).Sparepart murah juga dapat merusak kondisi dan kualitas fotokopi anda.
4. PILIHLAH TEMPAT STRATEGIS
Beberapa tempat strategis seperti:
  1. Sekolah / Universitas
  2. Pusat bisnis / Perkantoran
5. UTAMAKAN KUALITAS DAN PELAYANAN
  • Layanilah pelangan dengan senyum. Jika mereka puas, mereka pasti akan kembali walaupun harga anda lebih mahal dari pesaing
  • Berilah bonus-bonus secara berkala seperti bonus mika untuk pelanggan tetap
  • Tawarkan lah servis2 tambahan seperti: antar jemput gratis, fotocopy kilat, dll
  • Berilah bonus untuk pelanggan yg mereferensikan anda. 
    Contoh:
    Si B di rekomendasikan oleh si A untuk menggunakan jasa anda. Kemudian si A datang untuk fotokopi ke anda, dan anda memberikan diskon (sesuai kapasitas anda) untuk si A. Tentu saja, si A akan senang sekali dan kembali merekomendasikan anda kepada temannya.
  •  Bayangkan jika si A ada 50 teman saja.. berapa tambahan pelanggan yang anda dapatkan?

6. TIPS TUKAR TAMBAH
Apabila anda membeli Mesin Fotocopy dengan drum besar seperti IR5000, IR6000, usahakan untuk menjaga kondisi drum karena itu yang menentukan harga jual anda jika ingin tukar tambah mesin. Untuk informasi anda, harga drum berkisar antara 7jt - 8jt.
Jadi perawatan simple seperti:
- Pastikan Mesin Fotocopy terjaga kebersihannya
- pastikan tidak ada paper clip/staples yang berserakan dimesin saat fotokopi
- perawatan dan pembersihan corona wire dan miror-miror secara berkala
- Pakailah Tinta / Toner berkualitas dan jangan gonta ganti tinta
- Pastikan anda memakai penstabil tegangan listrik seperti Stabiliser

Mungkin itu dulu  Tips Usaha Copy Center dari saya moga bisa membantu para pemula yang ingin membuka usaha Fotocopy.
Artikel ini saya ambil dari forum, yang sudah saya tambahkan sedikit untuk melengkapinya saja.

Sumber: http://old.kaskus.co.id/showthread.php?t=6418637&page=4

Baca juga : Tips agar karyawan Fotocopy Anda betah

Enhanced by Zemanta

8 Point penting service berkala Fotocopy Canon Ir 4570

By photocopy canon | At Monday, November 19, 2012 | Label : , , , | 1 Comments
English: Photocopier Canon NP6521, cleaning, u...
English: Photocopier Canon NP6521, cleaning, unidentified part. (Photo credit: Wikipedia)
Photocopier
Photocopier (Photo credit: Joriel "Joz" Jimenez)
8 Point penting dalam pelayanan service berkala Fotocopy Canon ir4570 yang harus anda lakukan agar supaya mutu dan kualitas mesin foto copy anda tetap terjaga dan tentunya membuat mesin photocopy canon ir 4570 anda lebih awet.



Perhatian!
  • Jika Anda menggunakan pelarut, pastikan bahwa bagian-bagian itu telah benar-benar kering sebelum anda memsangnya kembali.
  • Kecuali bagian-bagian yang tidak memakai pelarut cukup pastikan kebersihannya saja.
  • Dalam panduan Service Manual Canon ir4570 ini tidak diperbolehkan menggunakan kain yang dibasahi dengan air.
  • Pastikan untuk memberikan pelayanan yang di jadwalkan pada interval tertentu atau menurut "Panduan Service Fotocopy Canon"

Untuk Jelasnya "8 Point penting service berkala Fotocopy Canon Ir 4570" bisa anda lihat pada gambar diatas serta keterangan dibawah ini:

[ 1 ] Copyboard glass, reading glass (clean, using water or mild detergent)
[ 2 ] Transfer/feed guide (clean; dry wiping)
[ 3 ] Fixing inlet guide (clean; dry wiping; alcohol)
[ 4 ] Photosensitive drum butting spacer (clean; dry wiping)
[ 5 ] Dust-blocking glass (clean; dry wiping or with alcohol)
[ 6 ] Waste toner collection case (check)
[ 7 ] Leakage breaker (check)
[ 8 ] Film bias static eliminator (clean)

Semoga Canon Ir4570 Ir3570 Ir2870 Ir2270 Service Repair Manual ini bisa bermanfaat bagi rekan-rekan dan jangan lupa klik tombol suka diatas atau tombol share yang ada dibawah agar bisa juga bermanfaat bagi teman-teman yang lain ok salam sukses untuk anda.

User tags: canon, printer copier fax ir4750 ir3750 ir2870, repair manual, service manual

 

Enhanced by Zemanta

Cara Ganti Drum NP6030 dengan benar

By photocopy canon | At Saturday, November 17, 2012 | Label : , , , | 4 Comments
REPLACING THE DRUM UNIT : Canon NP 6030.
Cara ganti Drum Unit Mesin Fotocopy Canon NP6030 dengan benar sesuai dengan prosedur penggantian Drum NP6030 yang ada pada buku Service Manual NP6030

Ikuti langkah-langkah "Cara Ganti Drum NP6030 dengan benar" :

Cara Ganti Drum NP6030 dengan benar ini belum di terjemahkan maklum saya tidak ahli untuk itu, jadi bagi rekan-rekan semua saya mohon maaf ya, tapi setidaknya dari gambar diatas anda sudah mempunyai "Panduan Cara Ganti Drum NP6030 dengan benar"
Oke sampai nanti kita di artikel lainnya ya jangan lupa untuk memberikan tanggapan/komentar dengan mencantumkan nama jelas dan sopan dalam menulis layaknya orang yang berpendidikan.


Kode Error Mesin Fotocopy Ricoh

By photocopy canon | At Thursday, November 15, 2012 | Label : , , | 0 Comments
Ricoh GR Digital II FirmwareUpdate V2.0
Ricoh GR Digital II FirmwareUpdate V2.0 (Photo credit: takuhitosotome)
Kode Error Mesin Fotocopy Ricoh [Error Codes Ricoh Copier] atau Technical SC CODE Ricoh adalah suatuh keadaan dimana Mesin Photocopy Ricoh memberitahukan letak kesalahan atau system error pada mesin fotocopy khususnya merek RICOH analog.

SC Code Ricoh

Dibawah ini saya berikan Kode Service [kode Error] Mesin RICOH Analog FT 7650

1.1 EXPOSURE

SC 101 - Exposure lamp malfunction - abnormal On/Off
Definition: [level: A]
During the lamp off condition, the optics control board detects a lamp voltage.

Possible causes
• Exposure lamp open
• Triac shorted
• Exposure lamp thermoswitch open
• Optics control board defective

SC 103 - Power source frequency detection error
Definition: [level: D]
Detects frequencies out of the 45Hz to 65Hz range.

Possible causes:
• Abnormal power source
• Electrical noise
• AC drive board defective
• Optics control board defective

SC  104 - Exposure lamp malfunction - abnormal off
Definition: [level: D]
The scanner start signal is received even if the main relay off condition is detected.

Possible causes:
• Main relay defective
• Communication error between the main control board and the optics control board because of a poor harness connection.
• Optics control board defective

Troubleshooting
1.2 SCANNER

SC 120 - Scanner home position sensor abnormal - stays off
Definition: [level: D]
The scanner home position sensor does not detect the on condition even if the scanner returns home.

Possible causes:
• Scanner home position sensor defective
• Optics control board defective

SC 121 - Scanner home position sensor abnormal - stays on
Definition: [level: D]
The scanner home position sensor does not detect the off condition even if the scanner leaves the scanner home position sensor by 120 mm.

Possible causes:
• Scanner home position sensor defective
• Scanner motor defective
• Scanner HP sensor short

SC 125 - Low scanner speed
Definition: [level: D]
The scanner speed, detected by the optics control board through the encoder, is lower than the specified speed.

Possible causes:
• Scanner drive motor defective
• Optics Control Board defective

SC 126 - High scanner speed
Definition: [level: D]
The scanner speed, detected by the optics control board through the encoder, is higher than the specified speed.

Possible causes:
• Scanner drive motor defective
• Optics control board defective

SC 127 - Scanner drive motor encoder failure
Definition: [level: D]
Scanner rotating direction detected by the optics control board through the encoder is opposite to the specified direction.

Possible causes:
• Scanner drive motor defective
• Optics control board defective

1.3 LENS MAGNIFICATION

SC 140 - Lens vertical home position sensor abnormal - stays off
Definition: [level: D]
When the lens returns to the home position, the lens vertical home position sensor does not detect the on condition for 2 seconds or more, and more than twice.

Possible causes:
• Lens vertical home position sensor shorted
• Lens vertical drive motor defective
• Optics control board defective

SC 141 - Lens vertical home position sensor abnormal - stays on
Definition: [level: D]
When the lens returns to the home position, the lens vertical home position sensor does not detect the off condition for 3.5 seconds or more, and more than twice.

Possible causes:
• Lens vertical home position sensor open
• Lens vertical drive motor defective
• Optics control board defective

SC 142 - Lens horizontal home position sensor abnormal - stays off
Definition: [level: D]
When the lens returns to the home position, the lens horizontal home potion sensor does not detect the on condition for 1.7 seconds or more, and more than twice.

Possible causes:
• Lens horizontal home position sensor short
• Lens horizontal drive motor defective
• Optics control board defective

SC 143 - Lens horizontal home position sensor abnormal - stays on
Definition: [level : D]
When the lens leaves from the home position, the lens horizontal home potion sensor does not detect the off condition for 2.3 seconds or more, and more than twice.

Possible causes:
• Lens horizontal home position sensor open
• Lens horizontal drive motor defective
• Optics control board defective

Troubleshooting
SC 144 - 3rd scanner home position sensor abnormal - stays off
Definition: [level: D]
When the 3rd scanner returns to the home position, the 3rd scanner home position sensor does not detect the on condition for 1.2 seconds or more, and more than twice.

Possible causes:
• 3rd scanner home position sensor shorted
• 3rd scanner drive motor defective
• Optics control board defective

SC 145 - 3rd scanner home position sensor abnormal - stays on
Definition: [level: D]
When the 3rd scanner leaves from the home position the 3rd scanner home position sensor does not detect the off condition for 2.0 seconds or more, and more than twice.

Possible causes:
• 3rd scanner home position sensor open
• 3rd scanner drive motor defective
• Optics control board defective

SC 146 - Abnormal magnification operation
Definition: [level: D]
The lens vertical drive motor or the lens horizontal drive motor move for no apparent reason in the ready condition.

Possible causes:
• Lens vertical drive motor defective
• Lens horizontal drive motor defective
• 3rd scanner drive motor defective
• Optics control board defective

1.4 OPTICS THERMISTOR

SC 190 - Optics thermistor open
Definition: [level: D]
The optics thermistor is open.

Possible causes:
• Optics thermistor open
NOTE: When the optics thermistor is shorted, no SC code is indicated. The exhaust fan rotates quickly and continuously.

SC 191 - Scanner motor thermistor open
Definition: [level: D]
The scanner motor thermistor is open.

Possible causes:
• Scanner drive motor defective

SC 192 - High Scanner Motor Temperature (70 CPM)
Definition: [level: D]
The temperature of the scanner motor is 80°C or more.

Possible causes:
• Scanner motor clooing fan defective

1.5 MAIN CHARGE

SC 302 - Charge corona leakage
Definition: [level: D]
The charge power pack detects a charge corona leakage (output: 0 V) for 4.8 ms, or detects the output to be more than 7 kV, 10 times in one job.

Possible causes:
• Main charge corona unit defective
• Main charge power pack defective
• High voltage control board defective

SC 303 - Charge corona wire cleaner failure
Definition: [level: C]
The current of the charge corona wire cleaner drive motor is over the specified current within 4 seconds after the cleaner motor starts. The charge corona wire cleaner does not move back to the end block within 30 seconds.

Possible causes:
• Charge corona wire cleaner drive motor defective
• Insufficient lubrication for the charge corona wire cleaner drive mechanism (G501 grease)
• High voltage control board defective

1.6 DEVELOPMENT

SC 341 - Development motor locked
Definition: [level: D]
Development motor lock signal stays low more than 1 second in development motor on condition.

Possible causes:
• Extra load in the development unit
• Development motor defective
• Main control board defective

SC 342 - Toner collection motor locked
Definition: [level: D]
The toner collection sensor output does not change (OFF/ON or ON/OFF) for more than 2.55 seconds in the toner collection motor on condition.

Possible causes:
• Toner collection sensor defective
• Toner collection motor defective
• Toner clog in the toner collection pipe

SC 343 - Toner collection bottle at improper position
Definition: [level: D]
Toner bottle set switch is off and the front door is closed.

Possible causes:
• Toner collection bottle set switch defective
• Toner collection bottle is set incorrectly

1.7 PROCESS SENSOR

SC 351 - Abnormal Vsg Detection (Vsg > 4.2V)
Definition: [level: C]
The detected Vsg value is over 4.2 V.

Possible causes:
• ID sensor defective
• Main control board defective

SC 352 - Incomplete TD sensor initial setting
Definition: [level: C]
The output voltage of the TD sensor is higher than 2.6 V or lower than 2.4 V during the developer initial setting mode. VOUT to get 2.5 V for the TD sensor output is higher than 10 V or lower than 2 V.

Possible causes:
• Connector [A] not set correctly
• Toner density sensor defective
• Abnormal toner concentration

SC 353 - Abnormal Vsp Detection (Vsp ³ 2.5 V: lighter pattern)
Definition: [level: C]
Vsp is 2.5 V or higher.

Possible causes:
• ID sensor defective
• OPC drum
• High voltage control board defective
• Poor contact of the development bias terminal [A] A176T502.wmf

SC 354 - Abnormal Vsg detection (Vsg £ 2.5 V)
Definition: [level: C]
Vsg is 2.5 V or less.

Possible causes:
• ID sensor defective
• OPC drum
• Dirty charge corona casing
• Quenching lamp defective
• Erase lamp defective
• Cleaning blade defective
• Dirty ID sensor

SC355 - Abnormal VTD detection (VTD ³ 4 V)
Definition: [level: C]
VTD is 4 V or higher.

Possible causes:
• Toner density sensor defective
• Toner concentration too low

SC 356 - Abnormal VTD detection (VTD < 0.5 V)
Definition: [level: C]
VTD is less than 0.5 V.

Possible causes:
• Toner density sensor defective
• Toner concentration is too high

SC 357 - Abnormal Vsp detection (Vsp/Vsg ³ 25%)
Definition: [level: C]
Vsp/Vsg is 25% or higher.

Possible causes:
• ID sensor defective
• OPC drum
• Dirty ID sensor

SC 358 - Abnormal Vsp detection (Vsp/Vsg < 2.5%)
Definition: [level: C]
Vsp/Vsg is less than 2.5%.

Possible causes:
• ID sensor defective
• OPC drum
• Toner scattering

SC 361 - Incomplete drum potential sensor calibration
Definition: [level: C]
When the process control initial setting is performed and a development bias of –100 V or –800 V is applied to the drum shaft, the drum potential voltage is out of these ranges: 0.1 £ V–100 £ 0.7 [V] or 2.7 £ V–800 £ 4.2 [V].

Possible causes:
• Drum potential sensor defective
• Drum shaft terminal not grounded
• OPC drum
• Main charge corona unit defective

SC 364 - Abnormal VD detection
Definition: [level: C]
VD is out of specification (VR + 770 ± 20 V).

Possible causes:
• Drum potential sensor defective
• OPC drum
• Main charge corona unit defective

SC 365 - Abnormal VL detection
Definition: [level: C]
VL is out of specification (VR + 140 ± 20 V).

Possible causes:
• Drum potential sensor defective
• OPC drum
• Main charge corona unit defective
• Optics too dirty


SC 366
Definition: [level: C]
VR is larger than 360 V in the process control initialization.

Possible causes
• OPC drum
• Drum shaft terminal not ground

1.8 TRANSFER CURRENT

SC 402 - Transfer current leakage
Definition: [level: D]
When the transfer power pack output voltage exceeds 4.5 kV for 200 ms or more, the output current is multiplied by 0.8. If this condition occurs 11 time in a row, an SC is displayed.

Possible causes:
• Transfer belt defective
• Transfer power pack defective
• Poor contact at transfer bias roller, discharge plate terminals

1.9 DRUM

SC 440 - Abnormal main motor speed
Definition: [level: D]
Lock signal stays low in the main motor on condition for 1.0 second or more.

Possible causes:
• Main motor defective

SC 442 - Drum thermistor open
Definition: [level: D]
The drum thermistor is open.

Possible causes:
• Drum thermistor defective

1.10 PAPER FEED

SC 500 - Abnormal manual feed drive motor speed
Definition: [level : D]
Lock signal stays low in the manual feed motor on condition for 1.0 second or more.

Possible causes:
• Manual feed motor defective

SC 501 - Abnormal paper feed drive motor speed
Definition: [level: D]
Lock signal stays low in the paper feed motor on condition for 1.0 second or more.

Possible causes:
• Paper feed motor defective
• Paper feed control board defective

SC 502 - Abnormal 1st lift motor movement
Definition: [level: B]
The 1st lift sensor detects high condition for 10 seconds or more after the 1st lift motor starts. The first time, after the paper tray is opened and closed, the 1st lift motor starts again. If the above condition occurs twice, this SC is displayed.

Possible causes:
• 1st lift sensor shorted
• 1st lift motor defective
• Paper feed control board defective

SC 503 - Abnormal 2nd lift motor movement
Definition: [level: B]
The 2nd lift sensor detects the high condition for 10 seconds or more after the 2nd lift motor starts. The first time, after the paper tray is opened and closed, the 2nd lift motor starts again. If the above condition occurs twice, this SC is displayed.

Possible causes:
• 2nd lift sensor shorted
• 2nd lift motor defective
• Paper feed control board defective

SC 504 - Abnormal 3rd lift motor (1.5 k LCT motor for A096 copier) movement
Definition: [level: B]
The 3rd lift sensor detects the high condition for 10 seconds or more after the 3rd lift motor starts. The first time, after the paper tray is opened and closed, the 3rd lift motor starts again. If the above condition occurs twice, this SC is displayed.

Possible causes:
• 3rd lift sensor shorted
• 3rd lift motor (1.5 k LCT motor for A096 copier) defective
• Paper feed control board defective

SC 506 - Abnormal 3.5 k LCT motor movement
Definition: [level: B]
The LCT lift sensor detects the low condition for 10 seconds or more after the LCT motor starts. The first time, after the LCT cover is opened and closed, the LCT motor starts again. If the above condition occurs twice, this SC is displayed.

Possible causes:
• LCT motor defective
• LCT lift sensor shorted

SC 507 - Abnormal 3.5 k LCT feed motor movement
Definition: [level: B]
The LCT feed motor is locked for 1 second or more after this motor starts.

Possible causes:
• LCT feed motor defective

SC 508 - Abnormal tandem rear fence drive motor movement
Definition: [level: B]
It takes 10 seconds or more for the rear fence return sensor to detect the on condition after the rear fence drive motor starts. It takes 10 seconds or more for the rear fence home position sensor to detect the on condition after this fence starts moving to the home position. When the tray is set, the rear fence return sensor and the rear fence the home position sensor are on.

Possible causes:
• Rear fence drive motor defective
• Rear fence HP sensor defective
• Rear fence return sensor defective

SC5 10 - Abnormal tandem side fence home position detection - stays off
Definition: [level: B]
When the side fence goes back to the home position or the side fence drive motor works to open the fence, the side fence positioning sensor does not detect the on condition for 5 seconds or more.

Possible causes:
• Side fence drive motor defective
• Side fence positioning sensor open

SC 511 - Abnormal tandem side fence home position detection - stays on
Definition: [level: B]
When the side fence goes back to the home position or the side fence drive motor works to close the fence, the side fence positioning sensor stays on for 5 seconds.

Possible causes:
• Side fence drive motor defective
• Side fence positioning sensor shorted

1.11 DUPLEX

SC 520 - Abnormal fusing/duplex drive motor movement
Definition: [level: D]
The lock signal stays low for 1.0 second after the fusing/duplex drive motor starts.
Possible causes:

• Fusing/duplex drive motor defective
• Cleaning roller is too dirty and applies a great load to the fusing/duplex drive motor.

SC 522 - Abnormal jogger home position sensor detection - stays off
Definition: [level: B]
The jogger home position sensor does not detect the on condition for 5 seconds or more after the fusing/duplex drive motor starts.

Possible causes:
• Jogger motor defective
• Jogger HP sensor open

SC 523 - Abnormal jogger home position sensor detection - stays on
Definition: [level: B]
The jogger home position sensor does not detect the off condition for 1 second after its sensor detects the on condition in the initializing mode.

Possible causes:
• Jogger drive motor defective
• Jogger HP sensor shorted

1.12 FUSING

SC 541 - Fusing thermistor open
Definition: [level: A]
Detects the fusing thermistor open condition for 2 ms or more after turning the main switch on.

Possible causes:
• Fusing thermistor open
• Optics control board defective

SC 542 - Start key stays red
Definition: [level: A]
The fusing temperature does not reach the specified temperature after 5 minutes from turning the main switch on.

Possible causes:
• Fusing lamp defective
• AC Drive board defective
• Fusing thermistor defective

SC 543 - Fusing overheat (detected by the main control board)


SC 544 - Fusing overheat (detected by the optics control board)
Definition: [level: A]
The fusing temperature stays over 231°C for 5 seconds.

Possible causes:
• AC drive board defective
• Fusing thermistor defective
• Optics control board defective
• Main control board defective

SC 545 - Low fusing temperature (detected by the main control board)

SC 546 - Low fusing temperature (detected by the optics control board)
Definition: [level: A]
The fusing temperature stays lower than 100°C for 5 seconds after the machine becomes ready.

Possible causes:
• Fusing thermistor defective
• AC drive board defective
• Fusing lamp open
• Main control board defective
• Optics control board defective

SC 547 - Fusing lamp continuously lit
Definition: [level: A]
Fusing lamp continuously lights for 70 seconds after the machine becomes ready. However, if the door is open, paper jams, or the fusing unit is out of position, the ready condition is canceled and the main relay opens.

Possible causes:
• AC drive board

SC 548 - Unstable fusing temperature
Definition: [level: A]
If the fusing temperature changes by 21°C/second four times in 1 minute, this SC is displayed.

Possible causes:
• AC drive board defective
• Thermistor defective

1.13 SYSTEM CONTROL

SC 600 - Communication error (main control board and operation panel)
Definition: [level: D]
The main control board does not communicate with the operation panel.

Possible causes:
• Main control board defective
• Operation panel defective
• Harness defective

SC 601 - Communication error (main control board and optics control board)
Definition: [level: D]
The main control board does not communicate with the optics control board.

Possible causes:
• Main control board defective
• Optics control board defective
• Harness defective

SC 603 - Main control board malfunction (CPU)
Definition: [level: D]
Communication to the main control board is not completed.

Possible causes:
• Main control board defective

SC 620 - Communication error (main control board and DJF/RDH main board)
Definition: [level: B]
The main board does not communicate with the DJF/RDH main board.

Possible causes:
• Main control board defective
• DJF/RDH main board defective
• Harness defective
• Fiber optics defective

SC 621 - Communication error (main control board and sorter staplers/finisher main board)
Definition: [level: D]
The main control board does not communicate with the sorter stapler/finisher main board.

Possible causes:
• Main control board defective
• Sorter stapler/finisher main board defective
• Harness defective
• Fiber optics defective

1.14 DUAL JOB FEEDER/RECIRCULATING DOCUMENT HANDLER

SC  700 - Abnormal DJF/RDH feed-in motor movement
SC  701 - Abnormal DJF/RDH transport belt motor movement
SC  702 - Abnormal DJF/RDH feed out motor movement
SC  703 - Abnormal RDH inverter motor movement

Definition: [level: B]
Encoder pulse is not detected by the DJF/RDH main board in the main motor on condition. The first time, a jam occurs. The second time, an SC is displayed.

Possible causes:
• DJF/RDH feed motor defective
• DJF/RDH transport motor defective
• DJF/RDH feed out motor defective
• DJF/RDH inverter motor defective

1.15 FINISHER/SORTER STAPLER

SC 730 - Abnormal *transport motor sorter stapler/finisher) movement
Definition: [level: D]
When the encoder pulse is not detected by the SS (or finisher) main board for 200 ms after the *transport motor starts, a jam is displayed. If this occurs twice, an SC is displayed.

Possible causes:
• *Transport motor
Sorter Stapler Finisher
* Main motor Transport drive motor

SC 731 - Abnormal bin drive (lift) motor movement (sorter staplers)
Definition: [level: B]
If the wheel sensor (bin lift timing sensors) is not off after 2 seconds from when the bin drive (lift) motor stars, jam "R2" is indicated. If the wheel sensor (bin lift timing sensors) is not on after 2 seconds from when the wheel sensor (bin lift timing sensors) detects off, jam "R2" is indicated.
If the condition above occurs twice, an SC is displayed.

Possible causes:
• Wheel sensor (bin lift timing sensors) defective
• Bin drive (Lift) motor defective

SC 732 - Tray shift motor (finisher)
Definition: [level: B]
The shift tray half turn sensor does not detect the on condition for 2 seconds after the finisher tray shift motor starts. The first time, a jam is indicated. The 2nd time, an SC is displayed.

Possible causes:
• Tray shift motor defective
• Shift tray half turn sensor defective

SC 733 - Shift tray lift motor (finisher)
Definition: [level: B]
The stack height sensor 1 or 2 do not detect the on condition for the specified time after the finisher shift tray lift motor.

Possible causes:
• Shift tray lift motor defective
• Stack height sensor 1 or 2 defective

SC 735 - Abnormal jogger motor movement (sorter staplers/finisher)
Definition: [level: B]
When the jogger moves back to the home position, the jogger home position sensor does not detect the on condition within 650 pulses. Then, a jam is indicated. When the jogger moves from the home position forward, and moves back to the home position, the jogger home position sensor does not detect the on condition within 100 pulses. Then, a jam is indicated.
If the above condition occurs twice, an SC is displayed.

Possible causes:
• Jogger motor defective
• Jogger home position sensor defective

SC 737 - Abnormal gripper motor movement (sorter staplers)
Definition: [level: B]
When the gripper moves to the staple position, the gripper home position sensor does not detect the on condition. Then a jam is indicated. When the gripper moves from the staple position to the bin position, the gripper home position sensor does not detect the on condition within 1070 pulses. Then a jam is indicated. When the gripper moves to the home position, the gripper home position sensor does not detect the on condition within 1.25 seconds. Then a jam
is indicated. When the gripper moves from the home position forward, and moves back to the home position, the gripper home position does not detect the on condition within 500 ms or more. Then a jam is indicated. If the above condition occurs twice, an SC is displayed.

Possible causes:
• Gripper motor defective
• Gripper home position sensor defective

SC 738 - Abnormal staple motor movement (sorter staplers)
Definition: [level: B]
The staple home position sensor does not detect the on condition within 600 ms after the motor starts. Then a jam is indicated. If this occurs twice, this SC is displayed.

Possible causes:
• Staple unit (staple motor) defective
• Staple is jammed in the staple unit.

SC 740 - Abnormal staple unit drive motor movement (sorter stapler/finisher)
Definition: [level: B]
The staple unit home position sensor does not detect the on condition when the staple unit is in the home position. A jam is indicated. The staple unit home position sensor does not detect the on condition (within 1640 pulses) when the staple unit moves to the home position. A jam is indicated. The staple unit home position sensor does not detect the on condition (within 280 pulses) when the staple unit moves forward from the home position and moves back to the home position. A jam is indicated. If the above condition occurs twice, this SC is displayed.

Possible causes:
• Staple unit drive motor defective
• Staple unit home position sensor defective

SC 741 - Abnormal bin rear plate motor movement (sorter stapler)
Definition: [level: B]
When the rear bin plate is open, the bin rear plate open sensor does not detect the on condition for 750 ms or more after the motor starts. Then a jam is indicated. When the rear bin plate is closed, the bin rear plate home position sensor does not detect the on condition for 750 ms or more after the motor starts. Then a jam is indicated. In the initial condition, the bin rear plate open sensor does not detect the on condition for 1.25 seconds or more after the motor starts. Then a jam is indicated.  If the above condition occurs twice, this SC is displayed.

Possible causes:
• Bin rear plate drive motor defective
• Bin rear plate open sensor defective
• Bin rear plate home position sensor defective

SC 742 - Abnormal stack feed out motor movement (finisher)
Definition: [level: B]
No encoder pulses is detected for 500 ms. or more.

Possible causes:
• Stack feed out motor defective

SC 743 - Punch motor abnormal (sorter stapler with punch)
Definition: [level: B]
When turning on the main switch, the punch home position sensor is not activated within 1100 pulses. Then an R2 jam is indicated. In punch mode, the punch home position sensor is not activated within 950 pulses after rotating the punch motor. Then an R2 jam is indicated. If
the above condition occurs twice, this SC is displayed.

Possible causes:
• Punch motor
• Punch home position sensor

SC 744 - Staple jam release abnormal (sorter stapler)
Definition: [level B]
In the initial condition the paper sensor is activated and the staple home position sensor is de-activated. Then, an R3 (staple) jam is indicated. If this condition occurs 4 times in a row, this SC is displayed.

Possible causes:
• Stapler

1.16 OTHERS

SC 900 - Total counter failure (staying in the off condition)
Definition: [level: D]
The total counter stays in the off condition.

Possible causes:
• Total counter defective

SC 901 - Total counter failure (staying in the on condition)
Definition: [level: D]
The total counter stays in the on condition.

Possible causes:
• Total counter defective SC full used toner bottle
Definition: [level: A]
The toner overflow switch is activated.

Possible causes:
• Toner collection bottle is full
• Toner overflow switch defective

NOTE: Clear the SC full used toner bottle as follows:
1) While the main switch is on, open the front doors then take out
the toner collection bottle (used toner bottle).
2) Remove the toner collection bottle then empty and clean the
bottle.
3) Install the empty toner collection bottle.
4) Close the front doors.

SC 940 - Main Switch Abnormal (U.S.A. version only)
Definition: [level: A]
The Main switch does not turn off after sending the reset signal two times in a row.

Possible causes:
• Main switch
• Main PCB

Download : ERROR SC CODE RICOH

Source Url: http://ricohservice.blogspot.com/
Enhanced by Zemanta

Instalasi Fax Canon imageRUNNER dan Cara Mengirim Fax dari PC Komputer

By photocopy canon | At Sunday, November 04, 2012 | Label : , , , , | 1 Comments
Cara Instalasi Fax Canon imageRUNNER dan Cara Mengirim Fax dari PC Komputer anda bisa ikuti langkah-langkahnya sebagai berikut ini:

1) Pertama Anda harus menambahkan mesin faks sebagai printer di bawah kontrol panel, ikuti langkah-langkah yang sama seperti anda menginstall driver printer fotocopy canon ir, memilih port IP yang sama seperti yang digunakan untuk mesin fotokopi Anda.

2) Sebelum mengirim pertama, Anda harus mengatur kontak umum Anda di Fax Address Book dan register your fax cover sheet.
  • Pilih "Print" dan memilih Canon Fax dari menu drop down. Selanjutnya pilih Properties
  • Sebuah kotak akan muncul (kanan), pilih "Add Person" dari sisi kanan.
  • Complete information for person, Anda juga dapat membuat grup disini 
  • Kemudian klik pada Register Cover Sheet, meng-upload sampul faks lembar dibuat dalam program Canon Cover Sheet Editor program (Sales Rep for assistance).. 

3) Cara Mengirim Fax dari PC Komputer
  • Pilih "Print" dan memilih Canon Fax dari menu dropdown. Tekan OK.
  • Sebuah kotak akan muncul pilih "Address Book" dan pilih penerima atau atau Masukkan nomor telepon dan pilih Add Recipient/tambah penerima.
  • Kemudian pilih Cover Sheet Tab dan Pilih sampul Anda, masukkan informasi pengirim dan komentar, Jika Anda menyimpan informasi pengirim, Anda bisa "mengimpor" pengaturan pengirim setiap kali untuk menghemat waktu Anda.
  • Di bawah Sender Dept / Div, gunakan bidang ini sebagai tanggal
  • Tekan OK!
Demikian pembahasan mengenai  Cara Instalasi Fax Fotocopy Canon Imagerunner (Canon ir) dan Cara Mengirim Fax Mesin Fotocopy ir dari pc komputer.
Untuk lebih jelasnya silahkan baca disini : Canon Cover Sheet Editor Program
Enhanced by Zemanta

Cara Menyimpan data di Mesin Fotocopy ke Flashdisk

By photocopy canon | At Friday, November 02, 2012 | Label : , | 13 Comments
English: A Sandisk-brand USB thumb drive, SanD...
English: A Sandisk-brand USB thumb drive, SanDisk Cruzer Micro, 4GB. (Photo credit: Wikipedia)
Cara Menyimpan data di Mesin Fotocopy ke Flashdisk atau cara memindahkan data dari photocopy canon ir (Image Runner 3245/35) ke flashdisk sehingga kita tidak perlu lagi membawa dukument2 kita untuk di copy, cukup membawa Flasdisk saja.

Oke kita langsung saja praktekkan Cara Menyimpan data di Mesin Fotocopy ke Flashdisk
  • Masukkan Flasdisk anda ke port USB yang berada disebelah kiri layar tuoch screen.
  • Pilih Mail Box USB dan tekan Memory Media.
  • Pilih Flashdisk Anda dan tekan open.
  • Pilih New Creation.
  • Nama folder Anda lalu tekan OK.
  • Pilih Scan.
  • Pilih Nama Dokumen.
  • Nama dokumen Anda dan tekan OK.
  • Pilih File Format.
  • Pilih PDF dan tekan OK. 
  • Kemudian, tekan tombol Start.
  • Setelah scan pertama, beralih ke halaman berikutnya dan tekan Start lagi. 
  • Ulangi langkah ini untuk beberapa halaman atau tekan Selesai sampai akhir.
  • Tekan tombol Remove USB. Tunggu konfirmasi sebelum menghapus drive USB dari mesin fotokopi, lalu tekan OK.
Selesai, semoga pembahasan mengenai  Cara Menyimpan data di Mesin Fotocopy ke Flashdisk bisa bermanfaat.
Anda juga bisa membaca artikel terkait ini "Cara Fotocopy Dari USB Drive Flashdisk"
Enhanced by Zemanta

Cara Fotocopy Dari USB Drive Flashdisk

By photocopy canon | At Friday, November 02, 2012 | Label : , | 6 Comments
English: USB flash drive Deutsch: USB-Speicher...
English: USB flash drive Deutsch: USB-Speicher-Stick (Photo credit: Wikipedia)
Cara Fotocopy Dari USB Drive Flashdisk di Mesin Fotocopy Canon Imagerunner (Canon iR) seperti Canon ir3245, ir3235, dan 3245i, ir3235i Series baca caranya dibwah ini:

Mencetak dari USB Flashdisk di Canon IR

  • Masukkan Flasdisk anda ke port USB yang berada disebelah kiri layar tuoch screen.
  • Pilih Mail Box USB dan tekan Memory Media.
  • Pilih perangkat Anda dan tekan open.
  • Pilih file yang ingin di cetak menggunakan tombol navigasi di layar dan tekan Start Print.
  • Pilih apakah ingin mencetak semua halaman atau halaman tertentu saja di "Print Range section"
  • Tambahan, Anda dapat mencetak secara bolak-balik (double-sided ) menggunakan tombol 2-Sided Printing.
  • Pilih Start Print.
CATATAN: Mesin Fotocopy Canon ir ini tidak mendukung file dokumen dari Microsoft Office . Canon Image Runner ini hanya mendukung file berformat PDF, TIFF, JPG. Jadi jika file yang ingin dicetak tidak tampil/keluar berarti Fotocopy iR ini tidak mendukung/tdk support dgn file anda..

Cara Fotocopy Dari USB Drive Flashdisk atau Print From USB Drive bisa juga anda baca disini Cetak dari USB Drive Copiers
Baca artikel terkait "Cara Menyimpan data di Mesin Fotocopy ke Flashdisk"
Enhanced by Zemanta
◄ Posting Baru Posting Lama ►

Ingin dapat tips-tips terbaru "Photocopy Canon" seperti cara-cara mengatasi Mesin Fotocopy error, servis manual, download driver dll secara gratis! silahkan masukkan Email anda pada kolom di bawah ini. Setiap artikel yang kami publikasikan, akan langsung kami kirim ke Email anda:

Delivered by FeedBurner

 

CARA PESAN:

PEMESANAN:
Silahkan anda menghubungi nomor-nomor dibawah ini untuk pemesanan mesin fotocopy maupun untuk bertanya seputar mesin fotocopy yang ingin anda beli dan juga untuk konfirmasi pembayaran.

CARA PEMBAYARAN:
Setelah informasi detail barang dan kesepakatan harga sudah ada persetujuan, silahkan melakukan pembayaran melalaui no rekening kami.

CARA PENGIRIMAN:
Apabila semua proses pembayaran dan konfirmasi sudah selesai dan sesuai, maka barang pesanan anda akan segera kami proses dan dikirim berdasarkan alamat pengiriman yang anda berikan kepada kami yang telah disepakati bersama.

PERSYARATAN:
Untuk pengiriman dalam area Jakarta atau radius 50km dari tempat kami tidak dikenakan ongkos kirim, sedangkan untuk luar kota dan luar pulau akan dikenakan ongkos kirim dan di tambah biaya packing sesuai dengan harga dari jasa

HUB Kami:

Jl. Raya Pagelarang

Komp KOPTI Blok C4 No. 13

Kel. Setu - Kec. Cipayung

Jakarta Timur 13880



Phone 021 9895 7421
Fax 021 8497 0328
Mobile 0812 8852 6006
Email 1
fendypoli@gmail.com
Email 2
fendypoli@yahoo.com

TRANSFER BANK


Copyright © 2012. MESIN FOTOCOPY CANON IR - All Rights Reserved