Error Code in Canon iR5000/iR6000

These are all list of Error Code in Canon iR5000/iR6000 more to come, i hope your machines works fine and never get error.

*E000

Main cause: the main thermistor (TH1) has poor contact or an open circuit.The thermal switch (TP1) has an open circuit.The fixing heater has an open circuit.The SSR is faulty.The DC controller PCB faulty.Mode of detection: 0000 after the main power switch is turned on,the temperature detected by the main thermistor does not reach 70ºC.
Caution: The error must be be reset in service mode (COPIER>FUNCTION>CLEAR>ERR)

*E001

Main cause: The main thermistor (TH1) has a short circuit.The sub thermistor (TH2) has detected overheating.The SSR is faulty.The DC controller PCB is faulty.Mode of detection:0001 The main thermistor or the sub thermistor has detected about 230ºC or higher for 2 sec.0002 The main thermistor has detected 230ºC or higher (hard circuit detection)0003 The sub thermistor has detected about 236ºC or higher. Caution: The error must be be reset in service mode (COPIER>FUNCTION>CLEAR>ERR)

*E002

Main cause: The main thermistor (TH1) has poor contact or an open circuit.The thermal switch (TP1) has an open circuit.The SSR is faulty.The DC controller PCB is faulty.Mode of detection:0000 The temperature of the upper fixing roller does not reach 100ºC within 2 min after it has exceeded 70ºC. Caution: The error must be be reset in service mode (COPIER>FUNCTION>CLEAR>ERR)

*E003

Main cause: The main thermistor (TH1) has poor contact or an open circuit.The thermal switch (TP1) has an open circuit.The fixing heater has an open circuit.The SSR is faulty.The DC controller PCB is faulty.Mode of detection:0000 The temperature detected by the main thermistor is 70ºC for 2 sec or more after it has reaced 100ºC. Caution: The error must be be reset in service mode (COPIER>FUNCTION>CLEAR>ERR)

*E004

Main cause: The SSR has a short circuit. The DC controller PCB is faulty.Mode of detection:0000 The SSR used to drive the fixing heater is found to have a short circuit (hard circuit detection). Caution: The error must be be reset in service mode (COPIER>FUNCTION>CLEAR>ERR)

*E005

Main cause: The fixing web has been taken up. The fixing web length sensor (PS45) is faulty.The DC controller PCB is faulty.Mode of detection:0000 The length of fixing web that has been taken up is in excess of the specified length. Caution: After replacing the fixing web, be sure to reset the two web counters in service mode:COPIER>COUNTER>MISC>FIX-WEB and COPIER>COUNTER>DRBL-1>FX-WEB.

*E010

Main cause: The main motor (M2) is faulty. The DC controller PCB is faulty.Mode of detection:0000 The clock pulse do not arrive for 2 secs or more after the main motor drive signal (MMFG) has been generated.

*E012

Main cause: The drum motor (M1) is faulty. The DC controller PCB is faulty.Mode of detection:0000 The clock pulses do not arrive for 2 secs or more after the drum motor drive signal (DMFG) has been generated.

*E013

Main cause: The waste toner feedscrew is faulty. The waste toner clock sensor (MSW2) is faulty. The DC controller PCB is faulty.Mode of detection:0000 The rotation of the waste toner feedscrew goes out of order, and the switch (MSW2) is pressed multiple times during a specific period of time.

*E014

Main cause: The fixing motor (M19) is faulty. The DC controller PCB is faulty.Mode of detection:0000 The motor clock signal is detected for 2 secs or more continuosly after the fixing motor drive has been generated.

*E020

Main cause: The hopper connector is left disconnected. The hopper motor (M9/M10) is faulty.The toner sensor (TS1/TS2) is faulty. The DC controller PCB is faulty.Mode of detection:0000 During printing, the toner supply is '0' (absence of toner) for 2 mins.

* E032

Main cause: The copy data controller or the remote diagnostic device is faulty. The main controller PCB is faulty.Mode of detection:0001 Although once connected,the copy data controlleror the remote diagnostic device has become disconnected.

* E061

Main cause: The laser shutter is faulty. The laser unit is faulty. The potential measurement PCB is faulty. The DC controller PCB is faulty.Mode of detection:0001 As the result of potential control,the drum surface potential (VL2) of the white background is about 200V
(generating solid black images).0002 The primary charging output used for print output and the drum surface potential after laser output has been made are about 200V (generating solid black images).

* E100

Main Cause: The BD PCB is faulty. The laser unit is faulty. The laser driver PCB isfaulty. The wiring is faulty (short circuit, open circuit). The DC controllerPCB is faulty.Mode of Detection:0001 In 100 msec after the laser drive signal has been generated, the BD signal is not detected 50 times or more
within 40 msecs.0002 While the laser is on, the BD signal cycle is found to be outside aspecific range 10 times or more.

* E110

Main Cause: The laser scanner motor (M15) is faulty. The wiring is faulty (short circuit,open circuit). The DC controller PCB is faulty.Mode of Detection:0001 • After the laser scanner motor drive signal has been generated,the motor ready signal (LMRDY*) does not arrive for
15 secs or more. (stop - full speed, half-speed - full speed)• During the period of 'full speed - half speed', the motor ready signal does not arrive for 60 secs or more after
the speed change signal has been generated.• During the period of 'full speed rotation', the motor ready signal is not detected 50 times or more (t intervals of 100 msec).

* E121

Main Cause: The controller cooling fan (FM4) is faulty. The wiring is faulty (short circuit,open circuit). The DC controller PCB is faulty.Mode of Detection0001 Although the controller cooling fan (FM4) is being driven, the clock signal (FM4LCK) does not arrive for 5 secs or more.
E196Main Cause: The EEPROM on the DC controller PCB is faulty. The location of the EEPROM is wrong. The DC controller PCB is faulty.Mode of Detection:1abb When data is written to the EEPROM, the data written and the data read do not match.2abb When the ID read into the EEPROM and the ID into the ROM are compared, a mismatch is found.3abb When ID in the EEPROM and the ID in the ROM are compared after the main power switch is turned on, a mismatch is found.a: chip Nos. 0 through 5 (0: IC104, 1: IC105, 2: IC109, 3: IC110, 4: IC127, 5: IC130)bb: chip faulty address (bit)

* E202

Main Cause: The scanner HP sensor (PS39) is faulty. The scanner motor (M3) is faulty. The reader controller PCB is faulty.Mode of Detection:0001 The scanner HP sensor does not turn off even when the scanner has been moved 40 mm forward after the main power switch has been turned on or the Start key has been pressed.0002 The scanner HP sensor does not turn on even when the scanner has been moved 450 mm in reverse.Caution No code is indicated, and keys are locked. The code may be checked in service mode (COPIER>DISPLAY>ERR).

* E204

Main Cause: The ADF controller PCB is faulty. The reader controller PCB is faulty.Mode of Detection:0001 During printing, the image leading edge signal does not arrive from the ADF.Caution No code is indicated, and keys are locked. The code may be checked in service mode (COPIER>DISPLAY>ERR).

* E220

Main Cause: The lamp inverter PCB is faulty. The reader controller PCB is faulty.Mode of Detection:0001 The lamp inverter PCB is found to have a fault.

* E225

Main Cause: The scanning lamp (xenon tube) is faulty. The inverter PCB is faulty. The CCD/AP PCB is faulty. The reader controller PCB is faulty.Mode of Detection:0000 A specific signal level cannot be attained by CCD gain correction at power-on.0002 The edge gain correction value changed more than a specific level compared with the correction value used for the preceding sheet.

* E240

Main Cause: The main controller PCB. The DC controller PCB is faulty.Mode of Detection:0000 An error has occurred in the communication between the main controller PCB and the CPU of the DC controller PCB.

* E243

Main Cause: The control panel CPU PCB is faulty. The main controller PCB is faulty.Mode of Detection:0000 An error has occurred in communication between the CPU of the control panel CPU PCB and the main controller PCB.

* E248

Main Cause: The EEPROM on the reader controller PCB is faulty. The reader controller PCB is faulty.Mode of Detection:0001 The ID read into the EEPROM when the main power switch has been turned on and the ID in the ROM do not match.0002 When data is written into EEPROM, the data written and the data read do not match.0003 When data is written, the ID in the EEPROM and the ID in the ROM are found not to match.

* E302

Main Cause: The CCD/AP PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty.Mode of Detection:0001 During shading, the reader controller PCB does not end shading in 1 sec.0002 In stream reading, the edge white accumulation (processing) does not end after a period of 10 secs.

* E601

Main Cause: The wiring is faulty (short circuit, open circuit). The hard disk drive is faulty. The DC controller PCB is faulty. The main controller PCB is faulty.Mode of Detection:0000 The main controller PCB has detected an error in control datawhile an image was transmitted between the main controller PCBand the hard disk drive.0001 The main controller PCB has found an error in the control data intransfer of images between main controller PCB and the DC controllerPCB.

* E602

Main Cause The wiring is faulty (short circuit, open circuit). The hard disk drive isfaulty. The main controller PCB is faulty.Mode ofDetection0001 A mount error was detected when the hard disk was started upfrom the boot ROM.0002 A data read error (from the hard disk) was detected when the harddisk was started from the boot ROM.

* E607

Main Cause The hard disk fan (FM7) is faulty. The wiring is faulty (short circuit, opencircuit). The DC controller PCB is faulty.Mode ofDetection0000 While the hard disk fan (FM7) is being driven, the clock signal(FM7CLK) does not arrive for 5 secs or more.

* E677

Main Cause The various printer board (accessories) are faulty. The main controller PCB is faulty.Mode ofDetection0001 An error has occurred in the communication between the various

* E710

Main Cause The DC controller PCB is faulty. The reader controller PCB is faulty.The main controller PCB is faulty.Mode ofDetection0001 When the main power is turned on, the IPC (IC5021) on the readercontroller PCB cannot be initialized.0002 When the main power is turned on, the IPC (IC120) on the DCcontroller PCB cannot be initialized.0003 When the main power is turned on, the IPC (IC1003) on the maincontroller PCB cannot be initialized.

* E711

Main Cause The connector is not connected properly. The remote diagnostic device PCBis faulty. The copy data controller PCB is faulty. The ADF controller PCB isfaulty. The ADF controller PCB is faulty. The finisher controller PCB isfaulty.Mode of Detection 0001 Data has been written to the error register of the IPC (IC5021) onthe reader controller PCB four times or more within 1.5 secs.0002 Data has been written to the error register of the IPC (IC120) onthe DC controller PCB four times or more within 2 secs.0003 Data has been written to the error register of the IPC (IC1003) ofthe main controller PCB four times or more within 2 secs.

* E712

Main Cause The connector is not connected properly. The ADF 24-V power supply isfaulty. The ADF controller PCB is faulty. The reader controller PCB isfaulty.Mode ofDetection0001 Communication does not resume in 3 secs after data has been writtento the error register of the communication IC (IPC) of the ADFcontroller PCB.0002 The transmission bit is not enabled after a period of 10 sec at thesync register of the IPC (IC5021) on the reader controller PCB.

* E713

Main Cause The connector is not connected properly. The finisher accessories powersupply PCB is faulty. The finisher controller PCB is faulty. The DC controllerPCB is faulty.Mode ofDetection0000 The communications IC (IPC) on the finisher controller has goneout of order.

* E717

Main Cause The wiring is faulty (short circuit, open circuit). The copy data controller orthe remote diagnostic device is faulty. The main controller PCB is faulty.Mode ofDetection0001 The copy data controller or the NE controller is out of order or anopen circuit has been detected.Caution The error must be reset in service mode (COPIER>FUNCTION> CLEAR>ERR).

* E719

Main Cause The wiring is faulty (short circuit, open circuit). The coin vendor is faulty.The main controller PCB is faulty.Mode of Detection0001 The communication between the coin vendor and the main controllerPCB has been interrupted.Caution The error must be reset in service mode (COPIER>FUNCTION>CLEAR>ERR).

* E732

Main cause The connector has poor contact. The reader controller PCB is faulty.Mode ofDetection0001 The main controller PCB has detected an error in the communicationbetween the reader controller PCB and the main controllerPCB.

* E733

Main cause The connector has poor contact. The DC controller PCB is faulty.Mode ofDetection0001 The main controller PCB has detected an error in the communicationbetween the DC controller PCB and the main controller PCB.CLEAR>ERR).printer boards (accessories) and the main controller PCB.

* E740

Main cause The LAN card is faulty. The main controller PCB is faulty.Mode ofDetection0001 An error is detected on the LAN card at power-on (with the cardinserted).0002 A MAC address is found to be faulty.0003 The LAN card register cannot be read.

* E741

Main Cause The PCI bus connection is not proper. The main controller PCB is faulty.Mode ofDetection0000 An error has occurred in the PCI bus.

* E742

Main Cause The RIP1 board (accessory) is faulty. The main controller PCB is faulty.Mode ofDetection0000 An error has been detected by self diagnosis of the RIPI board.

* E743

Main cause The connector has poor contact. The main controller PCB is faulty.Mode of Detection 0000 The reader controller PCB has detected an error in the communicationbetween the main controller PCB and the reader controllerPCB.

* E804

Main Cause The wiring is faulty (short circuit, open circuit). The DC power supply fan(FM6) is faulty. The DC controller PCB is faulty.Mode ofDetection0000 While the DC power supply fan is being driven, the clock signal(FM6CLK) does not arrive for 5 secs or more.

* E805

Main Cause The wiring is faulty (short circuit, open circuit). The feed fan (FM1) isfaulty. The heat discharge fan (FM3) is faulty. The DC controller PCB isfaulty.Mode ofDetection0001 While the heat discharge fan is being driven, the clock signal(FM3CLK) does not arrive for 5 secs or more.0002 While the feed fan is being driven, the clock signal (FM1CLK)does not arrive for 5 secs or more.

* E824

Main Cause The wiring is faulty (short circuit, open circuit). The primary charging assemblycooling fan (FM2) is faulty. The DC controller PCB is faulty.Mode ofDetection0000 While the primary charging assembly cooling fan is being driven,

* E412

Main Cause The cooling fan (FM1) is faulty. The ADF controller PCB is faulty.Mode ofDetection0001 While the cooling fan is being driven, the lock signal (FMLCK)arrives for 100 msec or more.

* E420

Main Cause The EEPROM is faulty. The ADF controller PCB is faulty.Mode of Detection 0001 When the host machine's power switch is turned on, the backupdata of the EEPROM cannot be read or the data, if read, has an error.

* E421

Main Cause The EEPROM is faulty. The ADF controller PCB is faulty.Mode ofDetection0001 Backup data cannot be written to the EEPROM or the data, if written,has an error.the clock signal (FM2CLK) does not arrive for 5 secs or more.

* E422

Main Cause The IPC communication has an error. The communication line has an opencircuit. The ADF controller PCB is faulty.Mode ofDetection0001 While the machine is in standby, the communication with the hostmachine has been interrupted for 5 secs or more. or, while the machineis in operation, the communication with the host machine hasbeen interrupted for 0.5 sec or more.

* E500

Main Cause The finisher controller PCB is faulty. The DC controller PCB is faulty.Mode ofDetection0001 The communication between the host machine and the finisher hasbeen interrupted; this error is detected by the host machine.

* E503

Main Cause The saddle stitcher controller PCB is faulty. The finisher controller PCB isfaulty.Mode ofDetection0002 The communication between the saddle stitcher controller PCBand the finisher controller PCB has been interrupted.

* E504

Main Cause The height sensor (PS1) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 Communication between the height sensor and the finisher controllerPCB is not possible, or communication data has an error.0002 Communication between the height sensor and the finisher controllerPCB is not possible for a specific period of time.0003 At time of power-on, the connector of the height sensor is found tobe disconnected.0004 When the height sensor is being adjusted using the DIP switch, anerror occurred during the adjustment.

* E505

Main Cause The EEPROM is faulty. The finisher controller PCB is faulty. The puncherdriver PCB is faulty.Mode ofDetection0001 When the power switch is turned on, the check sum of theEEPROM on the finisher controller PCB is found to have an error.0002 When the power switch is turned on, the check sum of theEEPROM on the puncher driver PCB is found to have an error.

* E512

Main Cause The delivery motor clock sensor (PI10) is faulty. The delivery motor (M2)is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 When operation starts, as many clocks as needed do not arrivefrom the delivery motor clock sensor.0002 No clock pulse arrives while paper is being moved over a distanceof 200 mm.

* E530

Main Cause The alignment plate home position sensor (PI6) is faulty. The alignmentmotor (M3) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 The alignment plate does not leave home position when the alignmentmotor has been driven for 2 secs.0002 The alignment plate does not return to home position when thealignment motor has been driven for 2 secs.

* E531

Main Cause The stapler home position detecting switch (MS7) is faulty. The stapler motor(M6) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 The stapler does not leave home position when the stapler motorhas been driven for 0.5 sec.0002 The stapler does not return to home position when the stapler motorhas been driven for 0.5 sec.

* E532

Main Cause The stapler shift home position sensor (PI7) is faulty. The stapler shift motor(M4) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 The stapler unit does not leave home position when the stapler shiftmotor has been driven for 4 secs.0002 The stapler unit does not return to home position when the staplershift motor has been driven for 4 secs.

* E535

Main Cause The swing motor clock sensor (PI20) is faulty. The swing guide open sensor(PI18) is faulty. The safety area switch (MS3) is faulty. The swing guideclosed detecting switch 2 (MS6) is faulty. The swing motor (M7) is faulty.The finisher controller PCB is faulty.Mode ofDetection0001 The swing guide closed detecting switch 2 does not turn on whenthe swing motor has been rotated CCW for 1 sec.0002 The swing guide open sensor does not turn on when the swing motorhas been rotated CW for 1 sec.0003 When the tray lift motor is in operation, the swing guide closed detectingswitch 2 is found to be off while the tray 1/2 is at OFF positionof the safety area switch.0004 No clock arrives for 200 msecs while the machine is in swing operation.

* E540

Main Cause The tray home position sensor (PI8) is faulty. The tray lifter motor clocksensor 1/2 (PI9/PI19) is faulty. The tray upper limit detecting switch (MS5)is faulty. The tray lifter motor (M5) is faulty. The finisher controller PCB isfaulty.0001 The ascent does not end in 15 secs when the tray lift motor isdriven; or, the tray home position cannot be detected when the traylift motor has been driven for 15 secs.0002 While the tray is moving up, the tray upper limit detection switchis found to be on.0003 When the tray lift motor is driven, clock pulses do not arrive fromthe clock sensor 1/2 for 200 msecs.

* E584

Main Cause The shutter open sensor (PI5) is faulty. The safety area detecting switch(MS3) is faulty. The shutter closed detecting switch (MS4) is faulty. TheNo. 2 feed motor (M8) is faulty. The finisher controller PCB is faulty.Mode ofDetection0001 The shutter closed detecting switch does not turn on when the No.2 feed motor has been rotated CCW for 1 sec or more.0002 The shutter open sensor does not turn on when the No. 2 feed motorhas been rotated CCW for 1 sec.0003 While the tray lift motor is in operation, the shutter closed detectingswitch is found to be off when the tray 1/2 is at OFF positionof the safety area detecting switch.

* E590

Main Cause The punch home position sensor (PI3P) is faulty. The punch motor (M1P)is faulty. The punch driver PCB is faulty.Mode ofDetection0001 The puncher does not leave home position when the punch motorhas been driven for 200 msecs.0002 The puncher does not return to home position when the punch motorhas been driven for 200 msecs.

* E593

Main Cause The horizontal registration home position sensor (PI1P) is faulty. The horizontalregistration motor (M1P) is faulty. The punch driver PCB is faulty.Mode ofDetection0001 The puncher does not leave home position when the horizontal registrationmotor has been driven for 4 secs.0002 The puncher does not return to home position when the horizontalregistration motor has been driven for 4 secs.

* E5F0

Main Cause The paper positioning plate home position sensor (PI7S) is faulty. The paperpositioning plate motor (M4S) is faulty. The saddle stitcher controllerPCB is faulty.Mode ofDetection0001 The paper positioning plate home position sensor does not turn onwhen the paper positioning plate motor has been driven for about1.3 secs.0002 The paper positioning plate home position sensor does not turn off1 sec after the paper positioning plate motor has been driven for 1sec.

* E5F1

Main Cause The folding motor clock sensor (PI4S) is faulty. The paper folding homeposition sensor (PI21S) is faulty. The folding motor (M2S) is faulty. Thesaddle stitcher controller PCB is faulty.Mode ofDetection0001 The number of detection pulses of the folding motor clock sensordrops below a specific value.0002 The state of the paper folding home position sensor does notchange when the folding motor has been driven for 3 secs.

* E5F2

Main Cause The guide home position sensor (PI13S) is faulty. The guide motor (M3S)is faulty. The saddle stitcher controller PCB is faulty.Mode ofDetection0001 The guide home position sensor does not turn on when the guidemotor has been driven for about 0.5 sec.0002 The guide home position sensor does not turn off when the guidemotor has been driven for 1 sec.

* E5F3

Main Cause The alignment home position sensor (PI5S) is faulty. The alignment motor(M5S) is faulty. The saddle stitcher controller PCB is faulty.Mode ofDetection0001 The alignment plate home position sensor does not turn on whenthe alignment motor has been driven for 0.5 sec (initially, drivenfor about 1.7 sec).0002 The alignment plate home position sensor does not turn off whenthe alignment motor has been driven for 1 sec.

* E5F4

Main Cause The stitch home position sensor (rear, MS5S) is faulty. The stitch motor(rear, M6S) is faulty. The saddle stitcher controller PCB is faulty.Mode of Detection 0001 The stitcher home position sensor (rear) does not turn off when thestitch motor (rear) has been rotated CW for 0.5 sec or more.0002 The stitch home position sensor (rear) does not turn on when thestitch motor (rear) has been rotated CCW for 0.5 sec or more.

* E5F5

Main Cause The stitch home position senor (front, MS7S) is faulty. The stitch motor(front, M7S) is faulty. The saddle stitcher controller PCB is faulty.Mode ofDetection0001 The stitch home position sensor (front) does not turn off when thestitch motor (front) has been rotated CW for 0.5 sec or more.0002 The stitch home position sensor (front) does not turn on when thestitch motor (front) has been rotated CCW for 0.5 sec or more.

* E5F6

Main Cause The paper push-on plate motor clock sensor (PI1S) is faulty. The paperpush-on plate leading edge position sensor (PI15S) is faulty. The paperpush-on plate home position sensor (PI14S) is faulty. The paper push-onplate motor (M8S) is faulty. The saddle stitcher controller PCB is faulty.Mode ofDetection0001 The paper push-on plate home position sensor does not turn onwhen the paper push-on plate motor has been driven for 0.3 sec ormore.0002 The paper push-on plate home position sensor does not turn offwhen the paper push-on plate motor has been driven for 0.3 sec ormore.0003 The paper push-on plate leading edge position sensor does not turnoff when the paper push-on plate motor has been driven for 0.3 secor more.0004 The number of detection pulses of the paper push-on plate motorclock sensor drops below a specific value.0005 The paper push-on plate leading edge sensor does not turn onwhen the paper push-on plate motor has been driven for 0.3 sec or more.

* E5F8

Main Cause The guide home position sensor (PI13S) is faulty. The paper push-on platehome position sensor (PI14S) is faulty. The paper push-on plate leadingedge position sensor (PI15S) is faulty. The saddle stitcher controller PCB isfaulty.Mode ofDetection0001 The connector of the guide home position sensor is found to bedisconnected.0002 The connector of the paper home positioning plate home positionsensor is found to be disconnected.0003 The connector of the paper push-on plate leading edge positionsensor is found to be discontented.

* E5F9

Main Cause The inlet door switch (MS1S) is faulty. The front door switch (MS2S) isfaulty. The delivery door switch (MS3S) is faulty. The saddle stitch controllerPCB is faulty.Mode of Detection 0001 When the inlet cover, front cover, and the delivery cover are foundto be closed, the inlet door switch detects an open condition for 1sec or more from the start of the initial rotation of the host machineor the start of printing.0002 When the inlet cover, front cover, and delivery cover are found tobe closed, the front door switch detects an open condition for 1 secor more after the start of the initial rotation of the host machine orthe start of printing.0003 When the inlet cover, front cover, and delivery cover are found tobe closed, the delivery door switch detects an open condition for 1sec or more from the start of the initial rotation of the host machineor the start of printing.


URL Shorten: http://brta.in/TX1vCiWK

Cara Repair Hardisk ir5000 / ir6000
Error E602-001 - Detail disini
Error E602-002 - Detail disini
Error E602-003 - Detail disini
Error E602-004 - Detail disini

45 comments:

Ardian Yudha mengatakan... Balas

mau tanya kalau e 202 itu kerusakan apa ya

Fendy Ch mengatakan... Balas

E000202-0001 Canon iR5000/iR6000
*Detection : Scaning Lamp Error, Sensor Scanner, check conector lamp and circuit Board.
(Reset Error : *28* - COPIER>DISPLAY>ERROR)

Pras mengatakan... Balas

Salam.
Bos ane mo tanya ni kalau ir 4570 E711 kenapa ya ?

Fendy Ch mengatakan... Balas

e711 - iR4570 iR3570 iR2270
1. The Inbox Memory is full
2. Erase the unnecessary documents stored in the box

Cara mengatasi:
1. Go into Service Mode. Press * Additional Functions, Press 2 and 8 number keys simultaneously, then Press * Additional Functions.
2. From the Service Mode screen. Select COPIER.
3. Select the FUNCTION tab.
3. Select CLEAR.
4. Under CLEAR, select PASSWORD.
5. Scroll to the second page and select PWD-CLR. Hit OK
Anda dapat mencoba PWD-CLR tetapi ini akan menghapus semua password.

OR,

You can do a HD-CLEAR in service mode the partitions on the imageRUNNER Hard Drive that hold this info is the Image Storage Area. So basically you need to select the partition you are going to format by selecting it with the CHK-TYPE option. This option is located at COPIER>FUNCTION>SYSTEM>CHK-TYPE in Service Mode.

Set the option from 0-x. They are described below: # 1 is the one you want to clear..

0 = Entire HDD
1 = image storage area
2 = multiple-use file storage
3 = PDL-related file storage area

2. After you selected the partition to format, you need to select HD-CLEAR. This option is located below CHK-TYPE in COPIER>FUNCTION>SYSTEM>HD-CLEAR.
Only perform any of these operations if you are familiar with doing them. Otherwise call for service if you not a tech.

e711 - iR5000 iR6000
1. IPC communication error
2. Cek kabel konektor ADF

heri mengatakan... Balas

tolonmg dong, mesin saya ir4570 kalau ngopy f4 atas turun 5 cm jadi yg bawah gak kebawa 5 cm cara perbaikinya gimana ?

Fendy Ch mengatakan... Balas

#Herri copy f4-nya lewat atas/ADF atau lewat Kaca/Platen Glass yg pernah sy alami f4 lewat ADF hslnya seperti itu.
Cara Mengatasinya:
Tekan *28* Copier>Option>Body>SCANSLCT bikin 1 (0:OFF 1:ON)
Moga berhasil!

doni mengatakan... Balas

bang kalo ir 5000 muncul error E001-003 itu apanya..
uda saya ganti thermistor kok tetap???
gimana kalo saya ganti fuse n thermostat???
apa pengaruh juga sama voltage listrik???thx

abbysoft mengatakan... Balas

Mau nanya gan, mesin photocopy saya ir6000 muncul pesan error E013 apanya yang rusak. mohon petunjuknya gan. Thanks

Fendy Ch mengatakan... Balas

Cek pembuangan limbah tinta/Waste toner (Penuh)
Cek juga sensor (MSW2) Limbah toner mungkin kotor tertutup debu/tinta

rocky mengatakan... Balas

Bang mau nanya juga, ir6000 saya disambung ke win7 kok gak mau kenapa yaa....(padahal klo ke win xp bisa) ....apa ada driver khusus untuk win7 ??? thk

Fendy mengatakan... Balas

Browsing aja cari driver canon iR6000 untuk windows 7 terus coba pakai kabel usb nya kalau hanya untuk ngeprint, karena selama ini pakai windows 7 memang agak ribet, kalau mau nyaman sich pakai xp aja. nanti kalau sempat saya posting cara koneksi canon iR untuk windows 7 nya ya.

Promo IR 6570 Berkwalitas mengatakan... Balas

Mohon bantuan Bos, mesin saya Ir6570 hasil tajam tetapi copy pada kertas F4 folio sering mengalami hasil pudar/hilang 1-2 cm secara horizontal. bagaimana solusinya?

HASBANUR mengatakan... Balas

salam kenal bos. saya punya ir 6000 kenapa kalo lg berhenti mesinnya keluar E 0712 tolong solusinya bos

photocopycanon mengatakan... Balas

Penyebab utama Konektor ADF tidak terhubung dengan benar.
ADF 24-V power supply rusak.
PCB kontroler ADF rusak. PCB reader controller ADF rusak.

Deteksi 0001
Dalam waktu 3 detik komunikasi data yang sudah di register terputus. IC komunikasi (IPC) di PCB controller ADF rusak.
Deteksi 0002
IPC ( IC 5021 ) pada PCB Reader Controller tidak mengirimkan/tidak diaktifkan setelah jangka waktu 10 detik.
Kemungkinan PCB Reader Controller/IC 5021 rusak

photocopycanon mengatakan... Balas

Anda masuk dgn id promosi Mesin Fotokopi ir6570 masak penjual ga bs service/ga py teknisi.
Kl mo nitip link ga usahlah pake ngetes segala to the point aja. untung komentnya masih berhgn dgn Photocopy kl ga da sy tandai spam ntar.

bambhard mengatakan... Balas

Mas Tolongmas mesin saya ir 6000 E 602-04 Solusinya gimana mas. tolong bantuannya mas

photocopycanon mengatakan... Balas

Silahkan baca artikel saya disini : Memperbaiki Error E602 001-004 memakai SST Tool Fotocopy Canon
Atau disini:
Help!!! E602 - 0004.
Semoga membantu, Terima kasih atas kunjungannya.

Ahmad K mengatakan... Balas

bos kalo mesin nya eror E000004-0000 kenapa ya??
terus gmn cara ngatasi nya????

isack mengatakan... Balas

mesin 6570 error 025-001, kerusakannya dimana dan cara mengatasinya

Anonim mengatakan... Balas

Bos..mohon bantuannya..kalo IR5000 kode errornya E000607-0000 rusaknya apa dan gimana cara ngatasinya?

Ari Basuki mengatakan... Balas

mesin saya ir5000 error E732 dan E14,apanya ya..

photocopycanon mengatakan... Balas

E732
Main cause The connector has poor contact. The reader controller PCB is faulty.
Mode of Detection
0001 The main controller PCB has detected an error in the communication between the reader controller PCB and the main controller
- Reader and Main controller tidak terhubung (cek konektornya)
- Tegangan 24V ke reader controller tidak ada (Cek PS reader controllernya)
- pada kondisi tertentu kemungkinan transformator HVT rusak

Yuli Putri mengatakan... Balas

Tolong donk... kalo aku switch on IR 6020 screen menunya gak ada yg cuman layar kosong, biasanya aku tekan on/off sampe beberapakali dalam 2 sampe 3 jam baru mau muncul screen menunya

Fendy Poli mengatakan... Balas

Mba Putri, coba dibersihkan dulu memory ram pakai penghapus pencil kl ga bisa cek Hardisknya.

java rudi mengatakan... Balas

gan mohon solusinya ir6570 ku cassete 3 tidak berfungsi malah muncul panah n ada tulisan stack bypass gt , mohon solusinya tks

Fendy Poli mengatakan... Balas

waduh ga berfungsi maksudnya gmn ya? ga mau narik, ga mau ngangkat,ato jamp atau apa nih. okelah coba bongkar kasetnya bersihkan semua sensor, ganti semua karetnya (biasanya kl ganti sebagian kdg masih ttp bermasalah), cek juga per2nya. dan mohon untuk bertanya ceritakan awal mulanya (Kronologisnya) biar cepat teratasi permasalahanya dan satu lagi jgn malas nulisnya ya hehehe... Trims sdh berkunjung

Anonim mengatakan... Balas

gan E000202-0101 CANON IR 5055 gmn solusinya

Fendy Poli mengatakan... Balas

cb periksa konektor lampu, sensor home position scanner, board controller untuk ADF dan coba periksa motor scanernya mungkin mutarnya berat (bersihkan.

Kabar Fakfak mengatakan... Balas

Bung Fendy...mau nanya...mesin saya canon ir 5075 baru tiba rekondisi error e000732-0001...pasa datang karena untuk menjaga kaca jangan pecah jadi kaca dilepas setelah disini baru dipasang...kira-kira bagaimana cara handlingnya...saya sudah coba buka lihat kabel pada lampu scaner ke board semua terkoneksi dengan baik (kencang)...jadi kira-kira apa yah...atau harus di reset tolong bung....makasih sebelumnya

Fendy Poli mengatakan... Balas

- Coba Check kabel reader unit ke main controller.(kabel soket belakang da terpasang dgn benar tidak? biasanya sih tidak terhubung dgn benar)
- Check suply tegangan ke reader unitnya
- Replace the reader controller PCB, reader relay PCB, or main controller PCB.
- Check the connection of the charger unit. (iR5075/5075N only.)

Anonim mengatakan... Balas

Gimana solusinya yah,, mesin saya ir 6570 error E000035-001. mohon pencerahannya. thanks.

Anonim mengatakan... Balas

bagai mana cara mengatasi E000732-0001 pada IR2870, tolong dbantu pak ?

Fendy Poli mengatakan... Balas

Error E000732-0001 Canon IR2870 sudah dibahas.silahkan baca komentar diatas. bagi komentor dimohon untuk interaktif agar masalahnya bisa diatasi/belajar bersama dan juga mohon bagi pengunjung yg sudah dikasih nama oleh orang tua pakailah nama anda dan bukan Anonim ya.

LUCKY mengatakan... Balas

MOHON BANTUAN BUNG FENDY ,MESIN SAYA IR 5000. KEMAREN NGEPRINT BUKU 1200 HAL. ADA HURUF YANG HILANG . MISAL: TRANS YANG DICETAK HANYA RANS ,HAL 600 YANG DICETAK HANYA 60. POSISINYA YANG HILANG TIDAK BERATURAN KADANG DI KIRI ,TENGAH, KANAN BAHKAN JUDULNYPUN HILANG SATU HURUF . MOHON PENJELASANYA BUNG. TRIM,S

LUCKY mengatakan... Balas

MOHON BANTUAN BUNG FENDY ,MESIN SAYA IR 5000. KEMAREN NGEPRINT BUKU 1200 HAL. ADA HURUF YANG HILANG . MISAL: TRANS YANG DICETAK HANYA RANS ,HAL 600 YANG DICETAK HANYA 60. POSISINYA YANG HILANG TIDAK BERATURAN KADANG DI KIRI ,TENGAH, KANAN BAHKAN JUDULNYPUN HILANG SATU HURUF .DRUM MASIH BAGUS SEKALI. MOHON PENJELASANYA BUNG. TRIM,S

Fendy Poli mengatakan... Balas

Coba di black copy dan lihat tanda putihnya cocok ga dengan besarnya huruf yang hilang.

dandy mengatakan... Balas

salam kenal bung fendi...type mesin canon apa yang cocok menggantikan ir 5000/6000 yang kebandelannya bagus buat copy center? dengar kabarnya stok ir 5000/6000 mulai agak susah yg kondisi bagus.

Fendy Poli mengatakan... Balas

Rekomendasi pakai Canon IR5020 atau IR6020 kalau dana minim alternatif lain bisa coba Canon IR5050 atau IR5070 dengan syarat anda harus menyiapkan stabilizer diatas 3000 watt. saya tidak menyarankan pakai Canon IR5570 atau Canon IR6570 kecuali yang sudah berpengalaman dan sudah terbiasa dengan error -error yang keluar pada Mesin Fotocopy Series ini. Xixixi..... Sorry para mania 55/6570 ya.

Anonim mengatakan... Balas

salamm kenal abang fendy
mesin saya error e 0000001-0010, sudah saya clearkan dengan program (COPIER>FUNCTION>CLEAR>ERR) tapi masih muncul juga e 0000001-0010
mohon dibantu infonya bang
terimakasih

muhlis ahmad mengatakan... Balas

siang gan ana mau tanya nih sy punya ir6020i klo sy photo copy hasilnya kepotong 1cm bagian atas dan kiri hasilnya??

bejo mengatakan... Balas

Mesin IR 5075 jika ADF dipasang keluar E000202-0101......kira2 apanya yg nggak beres gan ?
Tanpa ADF mesin jalan normal

mustahal mengatakan... Balas

Bung, numpang nanya nih, ir 6570 switch on screen menunya wait... terus, kira kira apa nya ya ? tolong dong.

yamin mengatakan... Balas

mohon maaf pa, nama saya yamin, pa saya baru pertama kali menggunanakan Mesin IR 6570, terus baru pertama usaha, ketika saya beli mesin saya bawa ke tempat usaha, mesing tersebut error, errornya E000004-0010, saya bingun pa, trus saya juga belum ada tekhnisi, pa bgmn solusinya untuk memperbaiki error tersebut agar mesin bisa bormal pa. mohon bantuan pa, skali lagi bantuan, atau ada solusi lain yang bisa saya pakai untuk memperbaikinya

Fendy Poli mengatakan... Balas

@yamin: Fotocopy Canon IR6570 Error E004-0010. coba direset COPIER>FUNCTION>CLEAR>ERR>OK. Mohon maaf baru dibalas

arief mengatakan... Balas

mohon bantuannya pak fendy. nama saya arief. mesin ir6570, ketika copy lebih dari 1 lembar, lembar pertama selalu terpotong kurang lebih 0,7 cm tetapi lembar kedua, ketiga seterusnya normal. terpotong di ujung awal lembar. kalau saya perhatikan posisi awal lampu laser mulai scan agak goyang, tidak dalam posisi diam. mohon solusi pak , terimakasih

Poskan Komentar

1. Mohon komentarnya sesuaikan dengan artikelnya ya!
2. Pakailah bahasa yang baik dan sopan
3. Pakailah nama sebenarnya bukan alias
4. Yang pakai Anonim/Anonymous tidak akan dijawab

No Spam, No SARA, No Po*no, No Iklan

◄ Posting Baru Posting Lama ►
 

CARA PESAN:

PEMESANAN:
Silahkan anda menghubungi nomor-nomor dibawah ini untuk pemesanan mesin fotocopy maupun untuk bertanya seputar mesin fotocopy yang ingin anda beli dan juga untuk konfirmasi pembayaran.

CARA PEMBAYARAN:
Setelah informasi detail barang dan kesepakatan harga sudah ada persetujuan, silahkan melakukan pembayaran melalaui no rekening kami.

CARA PENGIRIMAN:
Apabila semua proses pembayaran dan konfirmasi sudah selesai dan sesuai, maka barang pesanan anda akan segera kami proses dan dikirim berdasarkan alamat pengiriman yang anda berikan kepada kami yang telah disepakati bersama.

PERSYARATAN:
Untuk pengiriman dalam area Jakarta atau radius 50km dari tempat kami tidak dikenakan ongkos kirim, sedangkan untuk luar kota dan luar pulau akan dikenakan ongkos kirim dan di tambah biaya packing sesuai dengan harga dari jasa

HUB Kami:

Jl. Raya Pagelarang

Komp Primkopti blok A5 No. 2

Kel. Setu - Kec. Cipayung

Jakarta Timur 13880



Phone 021 8497 0328
Esia 021 9895 7421
Mobile 0812 8852 6006
Email 1
fendypoli@gmail.com
Email 2
fendypoli@yahoo.com

TRANSFER BANK